Skip to content
Kalighat Park, Stall No. 13, Kolkata 700026 pdutta1231@gmail.com +91 82740 66348
Geyser & Microwave Service — geyser and microwave repair in Kolkata

Geyser Installation & Uninstallation in Kolkata

Doorstep geyser installation and uninstallation across Kolkata for storage and instant models of all common brands – price agreed before any work starts.

  • Independent technician, all major brands
  • Price agreed before any work starts
  • Repairs at your home across Kolkata

How to get a quote

Most quotes start with a photo on WhatsApp. It takes a minute.

  1. Send a photoWhatsApp a photo of the geyser and its model sticker.
  2. Tell us the faultFor example: no hot water, leaking, tripping the MCB or making a noise.
  3. Quote or visitWe reply with an estimate, or book a technician visit to diagnose it.
  4. Price agreed firstThe full price is agreed with you before any work starts.

We install and uninstall geysers at homes across Kolkata – new storage and instant water heaters, like-for-like replacements, and old units taken down when you renovate or move. Installation covers mounting, the inlet and outlet connections, the safety valve, a wiring, MCB and earthing check, and a test run. The price is agreed before any work starts.

We are an independent service, not a brand or manufacturer’s service centre, and we install all the common geyser brands.

What’s included in a geyser installation

  • Checking the position – wall strength, clearance around the unit, distance to the power point, and room to reach the geyser later for servicing.
  • Mounting – drilling and fixing the brackets with fixings that suit your wall, so the geyser hangs level and secure. A full 25-litre tank weighs well over 30 kg, so this is not a job for a couple of plastic plugs.
  • Pipe connections – cold water to the inlet and the hot line from the outlet, connected the right way round (they are easy to swap by mistake), then checked for leaks at every joint.
  • Safety valve – fitting the pressure relief or multi-function valve supplied with the geyser on the inlet. It is never left out or blocked off.
  • Wiring and MCB check – a suitably rated socket and switch, a working earth, and an MCB that matches the geyser’s load. If anything is not right, we tell you before the geyser is connected.
  • Filling and test run – the tank is filled with water before the power goes on (heating an empty tank burns out the element), then a heating cycle is run to check the thermostat, the indicator lights and the joints.
  • A quick handover – where to switch it off, a sensible thermostat setting, and the warning signs worth acting on.

Some jobs need more than the standard fitting – a longer pipe run, an extra valve, a new socket or wiring for a point that was never meant for a geyser. Anything like that is quoted separately and agreed before it is done.

Safety first: a geyser should never be connected without an earth, and the safety valve should never be removed or plugged to stop a drip. A dripping valve is telling you something – usually about pressure or the thermostat – and it needs checking, not blocking.

Wall types: brick, tiled and concrete

The wall decides how the geyser is fixed, so tell us what kind it is when you book – or send a photo.

  • Brick walls – common in older Kolkata houses. Solid brick holds a geyser well, but old plaster can be crumbly, so the fixings go into sound brick rather than a mortar joint.
  • Tiled walls – most flat bathrooms. Tiles are drilled with a tile bit and without hammer action to avoid cracking. Old or hollow-sounding tiles are more likely to crack, and we point them out before drilling.
  • Concrete walls and columns – common in newer high-rise buildings. They need a hammer drill and take a strong fixing, but concealed water pipes and electrical conduits often run inside them, so tell us where those lines run if you know.
  • Lightweight block or partition walls – some newer flats use these. They may need special fixings or a different position for a large storage tank, and we tell you if the wall is not suitable.

Old geyser removal (uninstallation)

Taking down an old geyser safely is more than unscrewing it from the wall. The power is switched off at the MCB, the water supply is closed, and the tank is drained – after letting it cool, because an insulated tank keeps water scalding hot long after it is switched off. The pipes are disconnected, the unit comes off its brackets, and the open pipe ends are capped and the electrical point made safe if nothing is going straight back in its place.

We uninstall geysers for replacements, bathroom renovations and retiling, and house moves – common in Kolkata, where many families rent and take their geyser with them. If you are moving, we can take it down at the old flat and install it at the new one. An old safety valve that has been dripping is worth replacing at the same time.

Tell us when you book whether you want the old unit taken away, and we will confirm what is possible.

Brands we install

We install and uninstall all the common brands found in Kolkata homes, including Orient geysers, Bajaj geysers and Kenstar geysers, as well as Venus, Racold, AO Smith, Havells, V-Guard, Crompton, Jaquar and others. See all the brands we work on.

If you have just bought a new geyser, check your bill and warranty card first. Some brands and shops arrange installation through their own network, and some manufacturers ask for that to keep the warranty valid – in that case, using their installer is usually the simplest route. We are the alternative when installation is not included, when you need an old geyser taken down and moved, or when an existing installation needs putting right.

Instant or storage geyser?

If you have not bought the geyser yet, the type matters for installation as much as for daily use.

  • Instant geysers (usually 1 to 6 litres) suit a kitchen sink or a single wash basin. They heat a small amount of water quickly but cannot fill a bucket for a bath. They often draw more power than a storage unit, so the socket and wiring need to suit them.
  • Storage geysers (usually 10 to 25 litres) suit bathrooms. A 15 or 25-litre tank is the usual choice for a family bathroom. Horizontal models fit above a door or under a low ceiling where a vertical tank will not.

In compact flat bathrooms, wall space is often the deciding factor. Read instant vs storage geyser for Kolkata flats and what size geyser you need.

In tall buildings with a pressure pump, mention it when you book. The inlet pressure needs to suit the geyser’s rated pressure, which is printed on its rating plate.

Getting a quote for installation

Installation is priced on the job, not on a fixed list. The main factors are whether it is a like-for-like swap on the existing brackets or a new position, the wall type and mounting height, whether new connection pipes or valves are needed, whether the socket, MCB and earth are already suitable, and whether an old geyser has to come down first.

The quickest way to get an idea is to WhatsApp photos of the wall where the geyser will go, the pipe points and the power socket, along with the geyser’s brand and model. The full price is agreed before any work starts, with no hidden extras. Read how we quote and geyser installation: what’s included and what affects the cost.

Already installed and not working properly? See our geyser repair service.

Frequently Asked Questions

What is included in geyser installation?

Checking the position and wall, fixing the brackets, connecting the inlet and outlet, fitting the safety or multi-function valve, checking the socket, MCB and earthing, filling the tank and running a full heating cycle to test for leaks and correct operation. Extra pipework, valves or electrical work, if needed, are quoted separately and agreed before they are done.

How much does geyser installation cost in Kolkata?

It depends on the job: a like-for-like swap on existing brackets is simpler than a new position, and the wall type, mounting height, pipework and the state of the socket and earthing all matter. WhatsApp photos of the wall, pipe points and socket with the geyser model for an estimate. The full price is agreed before any work starts.

Can you install a geyser I bought online or from a shop?

Yes, we install all the common brands wherever you bought them. Check your bill and warranty card first: some brands and retailers include installation through their own network, and some manufacturers ask for that to keep the warranty valid. If installation is not included, or you need an old unit removed as well, we can help.

Can you remove my old geyser and fit the new one in the same visit?

Yes, that is the most common job. The old unit is switched off, drained once cool, disconnected and taken down, and the new geyser is fitted on the same or a new position. If the old brackets or valve are worn, we tell you before reusing or replacing them. Let us know when you book whether you want the old geyser taken away.

Can a geyser be fitted on a tiled or concrete wall?

Yes. Tiles are drilled with a tile bit and without hammer action to avoid cracking, and concrete needs a hammer drill and strong fixings. The main risk in concrete walls is concealed pipes or conduits, so tell us where they run if you know. Lightweight block or partition walls may need special fixings or a different position.

Does a geyser need its own MCB and earthing?

A geyser should have a working earth, a suitably rated socket and switch, and an MCB that matches its load – your geyser's manual gives the rating. Instant geysers often draw more power than storage models. We check these during installation, and if the wiring or earth is not right we tell you before the geyser is connected.

Request a call back

Leave your number and we will call you

Tell us the appliance, the brand and what it is doing. We call back, explain the likely fault and agree a visit time. The price is agreed before any work starts.

Prefer to talk now?

+91 82740 66348

    We only use your number to call you back about this request.